Search results

Rodger here are a couple of pictures from this site. I will post more of the restoration later. Rodger it now has a set of reproduction floor mats in the front and rear.

I am looking for a buyer, outside of the high end auction sites, for my 1972 FJ40. I purchased it from the original owner and it has less than 100K miles and has never had any rust or body damage. Frame off restoration, every nut and bolt, frame and all such parts powder coated. FJ is light blue...

I am looking for a NOS or used horn button for a 1972 FJ40. Anyone?

Took the FJ to it's first car show. I am not a big fan of car shows, but this was for a good cause. It is always interesting to be the only foreign car in a show. A show of mostly hot rods and Corvettes. A couple of the judges got it!

Found this story and was amazed that it is my FJ40 before I purchased it for restoration. You must start with a good example for a great restoration! http://www.originalpaintcars.com/rust-free-californian-1972-toyota-land-cruiser-fj40/

Once, I studied the system I was able to rebuild the Vacuum Control valve and get it all working correctly. Lots of bits and pieces involved in this analog system, but once understood it is relatively simple.

I am thinking about a roof rack. Has anyone had experience with Gobi? I am looking at this with the light bar, wind deflector, and rear drive side ladder. Thoughts? http://www.gobiracks.com/product/gobi-toyota-fj40-stealth/

Just finished my FJ40 restoration. The last project was installing gas struts inside my stock rear hatch lift tubes. This was a 10 minute project once the research was complete and the correct gas struts sourced. This was the idea project a completely rust free one owner FJ40 to start the...

I have looked at these used units but need a NOS unit. I know it is a needle in a hay stack, but I know people stash parts and I have had luck in finding most of what I need NOS when request posted. Let's see what is out there! Thanks Jerry Purcell

I am in need of a NOS Emission Evaporative Control Device for my 1972. I believe it is part# 17650-60012.

Sounds good, thanks!

I have an early FJ40 single barrel carburetor. It has not been overhauled. It is complete with bottom vent plate and insulator plate. Make reasonable offer or email for photos. [email protected]

I picked up a PTO winch for my 72 FJ40 last night. I need the following parts for install. 1. Drive shaft complete 2. Complete mounting frame 3. Linkage parts (at the transmission tunnel) 4. Any combination of these parts or a complete non-working unit for parts. Thanks JLP

I picked up a PTO winch last night but need the following parts for install: 1. Drive shaft 2. Mounting Frame complete 3. Linkage parts and lever that for transmission tunnel 4. Any combination of the above or a complete non-working unit that I can get these part from. Thanks for looking!

Bump back to top of list. Still looking for this item.

The light was also available painted. I ordered the painted one. I will de-grease it, scotch bright it and paint it with the original pewter. I have a quart from Cool Cruisers of Texas. I will post once complete. I still hold out hope of finding an original light for the dash.

Shayne, it will work until I find an original. The mounting hole is correct etc... So I ordered one to use but I will still be on the hunt for an original. Thanks for the heads up. jlp

There was a post on MUDD showing one went last year for over $100.00 US. They were standard on the factory soft top models and I believe it is the same light as some of the early FJ40 had mounted under the dash. They were standard equipment and I would like to fill the hole with the correct...

Still looking for this light. I know they are hard to find and expensive when you do. Please help me fill this hole in my dash with the proper map light. Thanks for your help.

Now have the brackets. Blasted powder coated and ready to install. I still need the rod extension. It is the rod without the hook on the end it has a collar with a bolt in it to hold it to the rod with the hooded end.

Mitch, I first put the smalls in a plastic container with a wire cloth bottom and a hole in the top to put my media blast nozzle through. I blast the parts then one at a time by hand wire brush them to a smooth finish. Some say that the wire brushing is not necessary, but the plating company I...

Mitch, hadn't checked the site for a few days. Sorry for not directly answering your questions. If I were you I, if you don't have one, I would buy a small blast cabinet. You can farm out the big parts for media blast (frame body etc...) but do the smalls yourself (bolts, brackets, etc...). On...

Bump to top of list.

Bump to top of list.

Bump to top of list.

I am looking for floor mats. I believe that I would like to go with a set of PVC form fitted for the front and rear. Input from anyone with experience in this area would be appreciated. SOR offers a set and I am in communication with a company in Australia which offers a PVC formed fitted...

bump to top

bump back to top

bump back to top

Thanks!

Thanks!