Search results

Francis, sorry for late response - i was not connected to the forum now its working... what i did back then was pushing the switch with my hand several times while blasting air on the microswitch all the time after several times the problem was gone for good - never happend again i stil have...

By adjusting the torsion bars you reduce or increase suspension pressure The height calibration done with height sensor and in some way can also influence on suspension pressures Look at the FMS for better understanding 2006 TLC 100 IL

Just for your info - the readings available : Pressure of accumulator Pressure at front right / left Pressure at rear Height front right / left Height rear Reading these parameters will help you to adjust / level car height, pressures, torsion bars The system carry part of the load and the...

The icarsoft can read the sensors - nothing more There are several test protocol that this box can do but I am not qualified for that With regard to the AHC. System - leveling, maintenance etc... There are few members here that help me solve my problems - suggest you speak with them first (uHu...

I didn't find the reason for any of the above issues and actually it's still happening from time to time - I figure out that there are few reasons - Leak somewhere or bed sealing High presser in the system Some defect part like valve or sphere or what ever I replaced the rear coil springs to...

No - I didn't check back then but when I had them side by side with the original ones they where shorter I can check the box or pull one of them out when I replace the rear shocks - one is bleeding I fly tonight for tow week - will get back to you when I have the info 2006 TLC 100 IL

I use the KTRS -79 at rear and they are shorter then original I didn't like it and I don't know if there's down side ... nowadays looking for beefier torsion bars - any idea? 2006 TLC 100 IL

Salty, My guess - fuel pump Mine has similar noise Once I open the cover while the engine was running and I could hear the noise clearly Unfortunately I broke the cover back then - be careful Back then I replaced the fuel filters and use add injectors cleaner to fuel Actually I used double...

I don't really know if there's an Oring on that shaft but it's look like something missing The lower ring on the shaft is metal ring Shaft diameter is 7.88mm and bearing diameter is 7.89mm so I assume that 0.01 means no wearing TLC 100 IL

The ugly part now - After taking apart the turbo I did few measurements- found nothing wrong!! I am not en expert and first time open a turbo but except the oil couldn't find problem in measures Any ideas or guideline will be appreciated ... TLC 100 IL

Hi everyone, Recently had white smoke when I start and later on while ramping up... Didn't think it coming from the turbo until it was too late... Heard piston knocking had to stop and check the engine. Diagnostic show no warning, oil level was low, car has 262,000 km Before pictures I now in...

Can't understand why someone want to have tires for years?! What's wrong with replacing tires every two to three years? I tried the copper, toyo, Yokohama and now the Goodyear which are quite surprising... I found out that the Goodyear MTR overall diameter gives one inch more if that's something...

I had confusion with forums... Anyhow the icarsoft pretty straight forward, easy to use and has all I need on the go. Keep it in my glove compartment The steering wheel as I learned has a role in the AHC system- while turning... Stability control too.. I know company in Israel that make...

Useful information I'm traveling twice a year to Murcia to visit customer and knew nothing about these regulations and fines Usually I fly to Madrid and drive to Murcia but never had a meeting with the police March 8-10 I will visit again - hope to see no police whatsoever Arnon TLC 100 IL

tlc 100 il

Hi uHu Finally had got the AHC oil and time to bleed the system... Replace 4-5 litter - saw that had air in the system and one of the rear shocks had really muddy fluid Next deal with the pressures and bring the front to spec front height was fine within 5mm side to side (-1 / -5) Rear was...

Hi Hali, Attached my LC VIN no etc Unfortunately do not have diff Locke at all Do I need to replace diff or it's possible to add original diff lock actuator? If I do need to replace the diff please quote Thank you Arnon TLC 100 IL

I can't really tel the difference since I have the car only for two month now but I notice a difference after replacing FR shock absorber I did some checking over the weekend reading heights and pressure in N height - Jan 30 morning: Height FR 6 mm FL 9.8 mm RR -9.2 mm Pressure: FR 7.7 RR 7.4...

Usually I wait minute or two before engine off unless it was very short drive - like 5 min This leveling process dose not happening every day - it is more like every couple of days I am going to service the AHC with fresh oil and bleeding each and every vent possible... Hope to get better...

Had a question I forgot to ask - I noticed that when I start the car on the morning it is leveling and raise up the from slowly It dose not happening every day but when it's happening it will be in the morning- first time I start the car. Is it normal? The height show N steady - no blinking...

Good News... I got my icarsoft i905 today ... Plug it into the DLC and it's working!!! Can read pressures and height of AHC and totally 52 sensors Here is what I getting: N position - front 7.5 rear 7.5 Pump / accumulator 10.5 H position - front 9.9 rear 8.5 L position- front 3.8 rear 6.9...

Thank you uHu Now it's clear.... Arnonmg

An update on my pedal - The new part arrived from Japan but before I gave up on the old pedal I tried to make it work It's turned out to be easier than i thought - cleaning the SW solved the problem ... I had the error message once a day and sometimes more and now zero! I was trying not to get...

Sorry for entering with my issues.... What ventilation controlled by the navigation system? What do I need to know before I delete my navigation? Mine is 2006 1HDJ-FTE VX An "I go" navigation was installed before my time and it's not working with the touch screen (has remote control) Maps...

uHu, I found this info at dtdauto they are having mobd for Toyota Will check the 13th pin when I get back home All the best Arnonmg

Thank you uHu Perfect explanation I download the FMS now and will get into the details Killing time in India ... Arnonmg

Yes Bob OME = old man... One point that need clarification - I assume Globes=Actuators ? Are they work as accumulator?? If they are kind of accumulators and their membrane wears off then the pump should show some warning like high temp Since AHC link to VSC / TRC I assume there will be other...

What if I replace torsion bars to OME ? How it's going to effect my AHC ? Note that I do not want to give up on the AHC but would like to get less tumbling at the front Appreciate your support ... Arnonmg

Will take few weeks - flying to India on Sunday for two weeks.. Arnonmg